Pipe Elbow Dimensions – Long & Short Radius Elbow Dimensions in mm

پائپ کہنی کے طول و عرض - لمبی اور مختصر رداس کہنی کے طول و عرض ملی میٹر میں

پائپ کہنی کے طول و عرض ASME B16.9 میں شامل ہیں۔ کہنی کے سائز 1/2″ سے 48″ کے طول و عرض کے لیے ذیل میں دی گئی جدول کو دیکھیں۔

NOMINAL PIPE SIZE	OUTSIDE DIAMETER	CENTER TO END
Inch.	OD	A	B	C
1/2	21.3	38	16	–
3/4	26.7	38	19	–
1	33.4	38	22	25
1 1/4	42.2	48	25	32
1 1/2	48.3	57	29	38
2	60.3	76	35	51
2 1/2	73	95	44	64
3	88.9	114	51	76
3 1/2	101.6	133	57	89
4	114.3	152	64	102
5	141.3	190	79	127
6	168.3	229	95	152
8	219.1	305	127	203
10	273.1	381	159	254
12	323.9	457	190	305
14	355.6	533	222	356
16	406.4	610	254	406
18	457.2	686	286	457
20	508	762	318	508
22	559	838	343	559
24	610	914	381	610
26	660	991	406	660
28	711	1067	438	711
30	762	1143	470	762
32	813	1219	502	813
34	864	1295	533	864
36	914	1372	565	914
38	965	1448	600	965
40	1016	1524	632	1016
42	1067	1600	660	1067
44	1118	1676	695	1118
46	1168	1753	727	1168
48	1219	1829	759	1219
All Dimensions are in mm

Pipe Fittings Dimensions Tolerance as per ASME B16.9

Pipe FIttings Quiz – Test yourself, Take This Quiz

NOMINAL PIPE SIZE	ALL FITTINGS	ALL FITTINGS	ALL FITTINGS	ELBOWS AND TEES	180 DEG RETURN BENDS	180 DEG RETURN BENDS	180 DEG RETURN BENDS	REDUCERS	CAPS
NPS	O.D. at Bevel (1), (2)	I.D. at End (1), (3), (4)	Wall Thickness (3)	Centre-to-End Dimension A,B,C,M	Centre-to-Centre O	Back-to-Face K	Alignment of Ends U	Overall Length H	Overall Length E
½ to 2½	0.06 -0.03	0.03	Not less than 87.5% of nominal thickness	0.06	0.25	0.25	0.03	0.06	0.12
3 to 3 ½	0.06	0.06		0.06	0.25	0.25	0.03	0.06	0.12
4	0.06	0.06		0.06	0.25	0.25	0.03	0.06	0.12
5 to 8	0.09 -0.06	0.06		0.06	0.25	0.25	0.03	0.06	0.25
10 to 18	0.16 -0.12	0.12		0.09	0.38	0.25	0.06	0.09	0.25
20 to 24	0.25 -0.19	0.19		0.09	0.38	0.25	0.06	0.09	0.25
26 to 30	0.25 -0.19	0.19		0.12	…	…	…	0.19	0.38
32 to 48	0.25 -0.19	0.19		0.19	…	…	…	0.19	0.38

NOMINAL PIPE SIZE NPS	ANGULARITY TOLERANCES	ANGULARITY TOLERANCES	ALL DIMENSIONS ARE GIVEN IN INCHES. TOLERANCES ARE EQUAL PLUS AND MINUS EXCEPT AS NOTED.
	Off Angle Q	Off Plane P	(1) Out-of-round is the sum of absolute values of plus and minus tolerance. (2) This tolerance may not apply in localized areas of formed fittings where increased wall thickness is required to meet design requirements of ASME B16.9. (3) The inside diameter and the nominal wall thicknesses at ends are to be specified by the purchaser. (4) Unless otherwise specified by the purchaser, these tolerances apply to the nominal inside diameter, which equals the difference between the nominal outside diameter and twice the nominal wall thickness.
½ to 4	0.03	0.06
5 to 8	0.06	0.12
10 to 12	0.09	0.19
14 to 16	0.09	0.25
18 to 24	0.12	0.38
26 to 30	0.19	0.38
32 to 42	0.19	0.50
44 to 48	0.18	0.75